Victron Multiplus C 24-2000-50 2000W Pure Sinewave Inverter Charger
KSh131,000.00 Ex-VAT
- Input Battery Voltage Range: 19 – 33 V
- Nominal AC Output Voltage: 230 VAC ± 2%
- Continuous Power Rating: 2000VA at 25 °C
- Peak Inverter Efficiency: 94%
- Waveform: Pure Sine Wave
- Nominal DC Input Voltage: 24V
- AC input Voltage Range: 187-265 VAC
- Frequency Range AC Input: 45 – 55 Hz
- Dimensions: 520x255x125
- Weight: 12kg
Victron Multiplus C 24-2000-50 2000W Pure Sinewave Inverter Charger
KSh131,000.00 Ex-VATRequest a Call Back
- Ask a Question
Victron Multiplus C 24-2000-50 2000W Pure Sinewave Inverter Charger
KSh131,000.00 Ex-VATAsk a Question
Victron Multiplus C 24-2000-50 2000W Pure Sinewave Inverter Charger
The Victron Multiplus C 24/2000/50 2000W Pure Sinewave Inverter Charger is, in one compact housing, a powerful sine wave inverter, a sophisticated charger
adaptive technology batteries, and AC transfer switch at high speed. In addition to these
main functions, the MultiPlus has several advanced features, as described below.
Two AC outlets
The main output has the “no-break.” The MultiPlus is responsible for the supply burden
connected during a power failure or disconnection of the main generator. This happens so fast (less than
20 milliseconds) that computers and other electronic equipment continue to operate without
interruption.
The second output is only active when one of the inputs of AC arrives at MultiPlus. This
output can be connected appliances should not discharge the battery, like a water heater by
example (second exit available only on models with 50 amp transfer switch).
Virtually unlimited power thanks to parallel operation
Up to 6 Multi’s can operate in parallel to achieve higher power output. Six units
24/5000/120, for example, will have a power output of 25 kW/30 kVA and a load capacity of 720
amps.
Three phase capability
In addition to parallel connection, three units can be configured in the same model for an output
phase. But that’s not all may be connected in parallel up to 6 sets of three units
provide an output power of 75 kW / 90 kVA and over 2000 amps of capacity.
PowerControl – limited generator, shore-side or network
The Multi is a very powerful battery charger. Therefore, use lots of electricity from the generator or the network
of the dock (about 10 A per Multi at 230 VAC 5kVA). The Multi Control Panel can establish
maximum generator power or shore. The MultiPlus will take account of other AC loads
and use the excess power to the load, thus avoiding overloading the generator or shore supply.
PowerAssist – Increase the power capacity of the shore or generator
This function takes the principle of PowerControl to another dimension. Allows the MultiPlus to supplement the
alternative source capacity. When required, peak power for a short space of time,
as often happens, MultiPlus immediately compensates the possible lack of power of the current
shore or generator with battery power. When the load reduces, the spare power is used
to recharge the battery.
Variable four-stage charger and battery banks charging double
The main output provides a powerful charge to the battery system using advanced software
“Variable load.” The software fine-tunes the three-stage automatic process to adapt to the
battery conditions and adds a fourth stage for long periods of slow loading. The process
variable load is described in more detail in the Phoenix data sheet Charger and our website,
see “Technical Information.” Besides this, the MultiPlus can charge a second battery
using a limited carrying out independent, designed to charge a battery to start the engine
main or the generator (this exit is only available in 12V and 24V models).
The system configuration can not be easier
Once installed, the MultiPlus is ready for operation.
If the configuration has changed, you can make in minutes using a new procedure
DIP switch configuration. With the DIP switches can even schedule
parallel operation and the phase: no computer needed!
You can also use a VE.Net instead of DIP switches.
And there is sophisticated software (Quick Setup and VE.Bus VE.Bus System Configurator) to set
several new and advanced features.
Technical Specifications
- Input Battery Voltage Range: 19 – 33 V
- Nominal AC Output Voltage: 230 VAC ± 2%
- Continuous Power Rating: 2000VA at 25 °C
- Peak Inverter Efficiency: 94%
- Waveform: Pure Sine Wave
- Nominal DC Input Voltage: 24V
- AC input Voltage Range: 187-265 VAC
- Frequency Range AC Input: 45 – 55 Hz
- Dimensions: 520x255x125
- Weight: 12kg
Based on 0 reviews
|
|
0% |
|
|
0% |
|
|
0% |
|
|
0% |
|
|
0% |
brand:
Related Products
- Input Battery Voltage Range: 38 – 66 V
- Nominal AC Output Voltage: 230 VAC ± 2%
- Continuous Power Rating: 3000VA at 25 °C
- Peak Inverter Efficiency: 95%
- Waveform: Pure Sine Wave
- Nominal DC Input Voltage: 48V
- AC input Voltage Range: 187-265 VAC
- Frequency Range AC Input: 45 – 55 Hz
- Dimensions: 362x258x218
- Weight: 18
- Rated AC power – 230V, Single phase.
- Max Supported Panel Power – 8 KWp
- Max Input Voltage (Voc) – 216V
- Charge Controller – PWM, 50Amps
- Nominal Battery Bank Voltage – 120V
- Of Batteries Required – 10 No’s
- Has In-built MOSFET Switching Element
- Input Battery Voltage Range: 9.5 – 17 V
- Nominal AC Output Voltage: 230 VAC ± 2%
- Continuous Power Rating: 1200VA @ 25 °C
- Peak Inverter Efficiency: 93%
- Waveform: Pure Sine Wave
- Nominal DC Input Voltage: 12V
- Nominal AC Input Voltage/Frequency: 187-265 VAC, 45 – 55 Hz
- Dimensions: 375x214x110mm
- Weight: 10kg
- Victron Phoenix Solar Inverter: 12/350 – 230V features
- Input Battery Voltage Range: 10.5V – 15.5V
- Nominal AC Output Voltage: 110VAC or 230VAC
- Continuous Power Rating: 350VA
- Peak Inverter Efficiency: 89%
- Waveform: Pure Sine Wave
- Nominal DC Input Voltage: 24V
- Dimensions: 72x155x237mm
- Weight: 3.5kg
- Model 650VA 850VA 1000VA 1450VA 2000VA
- Nominal Battery Voltage 12 VDC 24 VDC
- Solar Panel Connected to 50 Amps
- PWM/MPPT* Charge Controller (Max.)
- 850Wp 1700Wp
- AC Mains Mode
- Input Voltage Range (Eco Mode) 100 to 280 VAC ± 5 VAC (Wide Range)
- Input Voltage Range (Inv. Mode) 180 to 260 VAC ± VAC
- Changeover Time Maximum < 30 ms (in Eco Mode) and < 10 ms (in Inv. Mode)
- Charging Current (NC) 5A± 1A
- Charging Current (HC) 22A ± 1A
- Multifunctional, with intelligent power management
- Two AC inputs and two AC outputs
- Three phase capability
- Split phase options
- PowerControl – Dealing with limited generator, shore side or grid power
- Unique PowerAssist – Boosting the capacity of shore or generator power
- Input Voltage range: 38 to 66 Volt DC
- Output voltage: 230 Volts AC +/-2% @ 50 Hz
- Rated AC power – 230V, Single phase.
- Max Supported Panel Power – 1600 Wp
- Max Input Voltage (Voc) – 44V
- Charge Controller – PWM, 50Amps
- Nominal Battery Bank Voltage – 24V
- Of Batteries Required – 2 No’s
- Has In-built MOSFET Switching Element
- Power (2 AC Outlets): 600W Rated,1200W peak
- Max Efficiency 90%
- THD ≤3%
- USB output: 1xDC 5V/2.1A(max)
- Output wave form: Pure sine wave
- Nominal input voltage:12V(9.8-16VDC)
- Nominal output voltage: 110-120VAC
- Internal fuses:30A
- Battery cables(9AWG): one pair with a length of 2 ft.
- Remote controller: remote controller with 15ft cable. More convenient to control the inverter ON/OFF
- No load current:0.7A
- PowerControl: YES
- PowerAssist: YES
- Transfer switch (A): 50A
- Parallel and 3-phase operation: YES
- Input Battery Voltage Range: 19 – 33 V
- Nominal AC Output Voltage: 230 VAC ± 2%
- Continuous Power Rating: 1600VA @ 25 °C
- Peak Inverter Efficiency: 94%
- Waveform: Pure Sine Wave
- Nominal DC Input Voltage: 24V
- AC input Voltage Range: 187-265 VAC
- Frequency Range AC Input: 45 – 55 Hz
- Dimensions: 375x214x110mm
- Weight: 10kg
Reviews
There are no reviews yet.